Fully tempered glass for facades: structural requirements and design considerations


Release time:

Nov 10,2026

Article overview

Fully tempered glass is soda-lime glass heated to about 620°C and rapidly cooled, giving surface compression of at least 69 MPa, roughly four to five times annealed strength, and small blunt fragments on breakage. This guide covers facade specification in South Africa: structural requirements, SANS compliance, heat soaking, sizing, pricing and supplier checks.

Can fully tempered glass be used safely on a facade? Yes, provided wind load, support conditions, breakage behaviour and glazing position are checked together rather than separately. Many South African architects, aluminium fabricators and owners treat fully tempered glass as a simple upgrade on float glass. It is not. It is heat-treated glass with a distinct failure mode, and facade design has to respect that. The market is substantial: MarketsandMarkets puts the local float glass market at about US$1.08 billion in 2025, rising to US$1.75 billion by 2030 (10.2% CAGR), while local PFG capacity is about 260,000 tonnes a year. This guide is written for the comparison and pricing stage in 2026.

What fully tempered glass is and how it differs from other glass

Fully tempered glass is float glass strengthened by controlled heating and rapid cooling, and in South Africa "toughened" means exactly the same thing. The meaningful distinction is between fully tempered and heat-strengthened glass, not between two naming conventions.

How is fully tempered glass made?

Fully tempered glass is float glass reheated to about 620°C and quenched with air jets, locking the surface in compression and the core in tension. The outcome is tempered safety glass that is typically four to five times stronger than annealed glass of the same thickness. Think of it like a drawn bowstring: the outer skin is squeezed so hard that a surface flaw must overcome that compression before it can open. Because the stress is locked in, a pane cannot be cut, drilled or notched afterwards. Every hole, notch and edge finish is completed before the furnace. Wikipedia's overview of tempered glass explains the same principle in general terms.

Is fully tempered glass the same as toughened glass?

In local trade usage, yes. Toughened glass, toughened safety glass and fully tempered glass describe one product, and none is a higher grade. The real hierarchy runs annealed, heat-strengthened, fully tempered. Heat-strengthened glass cools more slowly and reaches 24–52 MPa surface compression under ASTM C1048. It breaks into larger pieces, so it is not safety glass on its own. Fully tempered glass must reach at least 69 MPa. Heat-treated glass is the umbrella term covering both.

Does tempered glass mean unbreakable?

No. When fully tempered glass fails, it fragments into small, blunt granules, which is a safety feature rather than immunity. It cannot replace laminated glass where burglar resistance or post-breakage retention is needed, and a hard point impact on the edge can still shatter a pane. Why do so many owners overlook this? Because the phrase "safety glass" sounds like a guarantee. It is not.

Common facade variants include clear toughened, laminated toughened, toughened insulating glass units (IGUs), Low-E coated toughened, heat soaked, and ceramic-frit or tinted versions.

Why specify fully tempered glass for facades at all? Because it combines load capacity, thermal tolerance and safe breakage in one product. Site experience commonly shows that problems are paperwork and process failures rather than strength failures: panes ordered before measurements were final, missing safety marks, or a toughened pane used where a laminated one was needed. Britannica's entry on safety glass outlines why tempering and lamination are distinct routes to safety.

Structural requirements for fully tempered glass facades

A facade pane must resist wind pressure, limit deflection, survive thermal stress and meet safety-glazing rules for its location. Fully tempered glass outperforms annealed glass on strength and thermal tolerance, but it demands attention at edges, supports and failure consequences.

Which SANS standards apply to facade glazing?

Four documents recur on South African projects. SANS 1263-1 covers SANS 1263 safety glass performance, including impact classification. SANS 10400-N sets where safety glazing is mandatory; critical locations such as doors, sidelights and low-level glazing normally require it. SANS 10137 governs glazing installation, and SANS 10160 supplies wind and imposed loads. Meanwhile SANS 10400-XA drives energy performance. For comparison, the US federal safety standard for glazing (16 CFR 1201) uses similar impact logic, although it is not a South African legal requirement. Always confirm clause applicability with your approved competent person.

How do wind load and deflection govern thickness?

Wind pressure from SANS 10160-3, pane dimensions and support type decide thickness. A four-edge supported pane behaves very differently from a two-edge or point-fixed pane. In practice, deflection often governs large facade panels before strength does, particularly in IGUs. Because deflection falls roughly with the cube of thickness, moving from 8 mm to 10 mm cuts deflection by about 49%. Typical thicknesses run from 6 mm to 12 mm, but no universal chart exists. Each project needs a calculation by a competent engineer or the processor's design service.

Under ASTM C1048, fully tempered glass must show a surface compression of at least 69 MPa or an edge compression of at least 67 MPa. (Paraphrased from the ASTM C1048 specification.)

Why do thermal stress and edge quality matter?

Sun on a partly shaded pane creates temperature differences between centre and edge. Using commonly quoted figures, annealed glass tolerates roughly 40°C, heat-strengthened about 100°C and fully tempered glass about 200°C. That is why heat-treated glass is standard behind spandrels and in tinted facades. Edges deserve equal care. Tension sits in the core, so chips and rough edges can trigger failure. Specify arrised or polished edges and protect them in handling. Visual quality matters too: roller wave and anisotropy, the "leopard spots" seen in polarised light, are inherent to heat treatment, so insist on a mock-up.

Fully tempered glass cannot be modified on site, so supports must absorb tolerances. Use gaskets and setting blocks to avoid glass-to-metal contact, keep drilled holes well clear of edges and corners, and in coastal zones specify grade 316 stainless fixings. For tempered glass panels longer than 2.5 m, confirm handling, transport and furnace limits early.

Fully tempered, heat-strengthened, laminated and annealed glass compared

Fully tempered glass wins on strength and safe breakage, laminated glass wins on retention after breakage, and heat-strengthened glass wins on flatness and resistance to spontaneous breakage. The right choice depends on position.

How do the strength and breakage figures compare?

Glass typeSurface compressionCharacteristic bending strengthBreakage patternThermal toleranceTypical facade use
AnnealedNegligible45 MPaLarge sharp shardsAbout 40°CLow-risk vision panels
Heat-strengthened24–52 MPa70 MPaLarger pieces, often stays in frameAbout 100°CSpandrels, high-rise vision glass
Fully temperedAt least 69 MPa120 MPaSmall blunt granulesAbout 200°CDoors, balustrades, safety zones
LaminatedDepends on litesDepends on litesCracks held by interlayerDepends on litesOverhead, balustrades, security

Sources: ASTM C1048 for compression; EN 12150, EN 1863 and EN 16612 for characteristic strengths; thermal values are commonly quoted figures. Confirm with your processor.

Laminated vs tempered glass: which belongs where?

Laminated vs tempered glass is not an either/or choice. Laminated glass holds fragments on an interlayer, so it suits overhead glazing, balustrades and security. Toughened glass doors and side panels use single-ply fully tempered glass because it resists impact and breaks safely. Where both are needed, laminated toughened glass combines them, at higher cost and weight. For a frameless glass balustrade, many designers specify laminated toughened so the handrail line stays retained if one ply fails. Tempered glass shower screens, by contrast, are almost always single-ply.

  • Entrance doors and sidelights: fully tempered glass or laminated toughened.
  • Overhead and canopy glazing: laminated, often with heat soaked tempered glass.
  • Spandrel and shadow-box panels: heat soaked or heat-strengthened glass.
  • Interior partitions and shower enclosures: single-ply fully tempered glass.

When is heat-strengthened glass the better facade choice?

Choose it when flatness, spontaneous breakage risk or thermal stress outweighs impact safety. Heat-strengthened glass shows less roller wave and rarely breaks spontaneously, so large reflective facades often use it. Of course, there are exceptions: where the pane is within reach of people and must act as safety glass, fully tempered glass or laminated glass is required.

Spontaneous breakage and heat soaked tempered glass

Nickel sulphide (NiS) inclusions can cause rare, delayed breakage in fully tempered glass, and heat soaking reduces that risk without eliminating it. Heat soaked tempered glass is therefore standard on high-rise, overhead and high-consequence facades.

What causes nickel sulphide breakage?

NiS stones are microscopic particles formed in the melt. After tempering, they slowly change crystal phase and expand, which can overload the tensile core and shatter the pane, sometimes years after installation. Published breakage estimates vary widely with raw materials and batch, so treat any single figure with caution. A pane that breaks spontaneously often shows two small "butterfly" fragments at the origin, which helps forensic diagnosis.

How does the EN 14179 heat soak test work?

The heat soak process in EN 14179 deliberately breaks susceptible panes in the oven rather than on site:

  1. Load tempered panes into a calibrated heat soak oven with surface thermocouples.
  2. Heat until the glass surface reaches 290°C ±10°C.
  3. Hold that temperature for the specified period, normally two hours.
  4. Cool the load under controlled conditions and remove any broken panes.
  5. Record the batch, cycle data and certificate for traceability.

Is heat soaking always necessary?

No. It adds cost and lead time, and it cannot remove the risk entirely. For low-level balustrades or interior partitions, many projects accept standard fully tempered glass. For overhead glazing, tall facades or areas above public spaces, specify heat soaked tempered glass and combine it with laminated build-ups where fall-out would be hazardous. Ask the processor for the oven certificate, not a verbal assurance.

Fully tempered glass fragmentation sample and polarised light stress pattern

A fragmentation sample and a polarised-light view of the pane make useful acceptance checks. The sample should show fine, blunt granules, and the stress pattern should look even across the pane. Other risk-reduction measures include using heat-strengthened glass, laminating the build-up, designing for easy replacement of individual lites and keeping spare panes from the same batch. A small residual risk remains, which is why an honest supplier will not promise zero breakage.

Design considerations for South African conditions

South African facades face intense UV, coastal salt, summer storms and occasional hail, so specify around the environment rather than the data sheet. Fully tempered glass itself is largely unaffected by UV and salt; the surrounding sealants, coatings, interlayers and fixings are what age first.

How do hail and storm impact affect fully tempered glass?

Fully tempered glass resists hail far better than annealed glass of equal thickness, yet severe events with large stones can still break panes, particularly at damaged edges. No glass type is hail-proof. Where hail risk is high, as on parts of the Highveld, laminated toughened glass limits fall-out. Insurers may also have requirements, so check before ordering.

What do coastal and UV exposure change?

Salt mist deposits on the surface and attacks aluminium frames and weak hardware. Specify grade 316 stainless fixings and quality anodising or powder coating, and rinse glass with fresh water regularly; coastal owners might do so monthly. High UV degrades low-grade sealants over time. Warranty terms differ between processors, so read the exclusions carefully.

What do SANS 10400-XA rules mean for glass choice?

A 2026 trend is energy compliance. SANS 10400-XA:2021 Ed.2 pushes designers towards Low-E coatings, insulating glass units and tempered build-ups to meet shading and U-value targets. Not every coating survives the furnace, so specify a "toughenable" Low-E product and confirm which pane is tempered. Absorptive tinted glass heats faster, which raises thermal stress and often pushes the specification to heat-treated glass. Imports add uncertainty: ITAC maintains a 27.26% anti-dumping duty on Egyptian float glass and has applied a temporary duty on Tanzania, so price and lead-time swings are possible.

Visual checks matter on large elevations. Roller wave and edge distortion are most visible in reflective glass, so view a full-size sample at the real viewing angle. Inspect edges during installation, because a small chip today can become a failed pane after a few summers.

Sizing and selection: a worked example

Selecting fully tempered glass means moving from inputs to a checked section: define loads, support, size and failure consequence, then verify with an engineer. The example below shows the logic, not a design.

What steps lead to the right thickness?

  1. Confirm the glazing position and the SANS 10400-N safety-glazing requirement.
  2. Obtain design loads from SANS 10160 (wind, and imposed line load for balustrades).
  3. Fix the support condition: four-edge, two-edge, channel or point-fixed.
  4. Estimate bending stress and deflection for trial thicknesses.
  5. Decide whether laminated, heat soaked or Low-E variants are needed.
  6. Finalise sizes, holes and edges before ordering, then obtain written engineering sign-off.

Worked example: cantilevered frameless balustrade

Assume a 1.0 m high cantilevered pane fixed in a base channel, carrying a 1.0 kN/m horizontal line load at the top. Per metre width, the base moment is 1.0 kNm. Bending stress equals moment divided by section modulus, where Z = b × t² / 6.

ThicknessSection modulus per metre (mm³)Bending stress (MPa)Observation
10 mm16,66760.0Highest stress, likely marginal
12 mm24,00041.7Common trial thickness
15 mm37,50026.7Lower stress, higher cost and weight

Against a characteristic bending strength of 120 MPa for toughened soda-lime glass, all three sit below the limit before partial factors, load duration and deflection limits are applied. Those factors cut usable stress sharply, and deflection at the top of a cantilever often governs tall balustrades, so a stress pass alone is not approval. Real projects often use laminated toughened glass, with loads from SANS 10160-2 for the occupancy. Treat this as an illustration only.

When you brief a processor, send the following:

  • Dimensioned drawings, with hole and notch positions.
  • Thickness, edge finish and coating or silkscreen requirements.
  • Heat soak requirement, quantities and site location.

Illustrative scenario: coastal apartment

Consider a hypothetical Cape Town sea-facing apartment with a balcony balustrade and a sliding door. A sensible brief might specify laminated toughened balustrade glass, single-ply fully tempered glass for the door leaves, 316 stainless hardware and heat soaked panes on any overhead section. This is a scenario, not a client project, but it shows how position drives specification.

Cost, suppliers and compliance checks in South Africa

Budget by thickness first, then add processing, heat soaking, delivery and installation, and always compare quotes on the same basis. Quotes differ mainly because they cover different things.

What is the tempered glass price per square metre in 2026?

The tempered glass price per square metre varies with thickness, size, coating and market conditions. The planning bands below are broad budgeting allowances for ex-VAT supply in rand, not a published price list. Replace them with written quotes.

ItemIndicative planning band (R/m², ex VAT)Notes
6 mm clear toughenedR450–R750Screens and smaller panes
10 mm clear toughenedR750–R1,200Doors and balustrades
12 mm clear toughenedR950–R1,500Larger panes
Laminated toughened (2 × 6 mm)R1,300–R2,300Interlayer included
Heat soak, holes, silkscreen, polishingQuoted separatelyPer pane, hole or m²

Processing is where quotes diverge. Holes, notches, polished edges, silkscreen and heat soaking are usually charged per item, per linear metre or per square metre, and delivery and installation may sit outside the glass price. Local float capacity of about 260,000 tonnes a year supports domestic processors, yet imported glass remains in the mix, so lead times can shift.

How do I find reliable local suppliers?

Gauteng and the Western Cape both have established processors. Whether you are searching for tempered glass suppliers Johannesburg or glass cut to size Cape Town, the cutting stage matters because dimensions are frozen before tempering. Ask about custom tempered glass South Africa capability: maximum sheet size, lead time, heat soak oven and logistics. Use glaziers experienced in SANS 10137 installation, and request references. Then run this checklist:

  1. Check that each pane carries a permanent SANS 1263 mark etched in a corner.
  2. Request SABS certification or test evidence for the product, not just the supplier.
  3. Confirm maximum size, thickness range and current lead time in writing.
  4. Ask whether heat soaking is available and request the cycle certificate.
  5. Compare quotes on supply, processing, delivery, installation and breakage terms.
  6. Get the warranty period and exclusions in writing.

What warranty and maintenance should you expect?

Warranties differ, so treat any verbally quoted period with caution. Most cover manufacturing defects, not impact damage, edge chips from site handling or incorrect installation. Clean with non-abrasive products, avoid scraper blades, and inspect edges and seals annually.

Frequently asked questions

Q: Is fully tempered glass stronger than toughened glass?

A: No. In South Africa they are the same product. The real comparison is fully tempered versus heat-strengthened or annealed glass, where fully tempered glass reaches at least 69 MPa surface compression and is roughly four to five times stronger than annealed glass.

Q: Can fully tempered glass be cut or drilled after tempering?

A: No. Internal stress means cutting or drilling after tempering will shatter the pane. Final dimensions, holes, notches and edge work must be fixed before the furnace, so confirm measurements twice before ordering.

Q: Does fully tempered glass need heat soaking for facades?

A: Not always, but it is recommended for overhead, high-rise and high-consequence glazing. Heat soaking to EN 14179 reduces nickel sulphide breakage risk without removing it, so ask for cycle certificates and consider laminated build-ups.

Q: How do I verify SANS 1263 compliance?

A: Look for the permanent etched mark on the pane, then request the supplier's certification or test evidence and keep it in your project file. If marks are missing or unclear, ask for clarification before installation.

Q: Can toughened glass replace laminated glass?

A: Not where retention after breakage, security or fall protection matters. Fully tempered glass breaks safely into granules but does not stay in place. Laminated or laminated toughened glass is the usual choice for overhead glazing and balustrades.

Fully tempered glass for facades works best when it is specified as part of a system: confirmed loads, SANS-compliant marking, correct edge and hole detailing, heat soaking where risk justifies it, and laminated build-ups where retention matters. Define sizes early, compare quotes on one basis and verify documents before delivery. For project-specific decisions, consult a qualified glazing engineer. Done properly, fully tempered glass delivers durable, safe and efficient facades across South Africa's demanding climates.